Leak Detection in Eddy, TX — Find It Before You Open a Wall
The difference between a $300 pipe repair and a $3,000 drywall-and-remediation project is often just whether the leak was found before or after excessive wall opening. Our Leak Detection service in Eddy uses the same detection methods utilities and insurance adjusters rely on — to pinpoint the failure location before anything is cut.
The Tools Behind Accurate Leak Detection in Eddy, TX
No single detection method works for every leak scenario. Our technicians are trained on four distinct approaches and select the right tool — or combination of tools — based on the pipe type, building construction, and leak characteristics.
🎙️
Acoustic Ground Microphone
Pressurized supply line leaks create a distinctive low-frequency sound as water escapes the pipe and contacts surrounding soil or structure. Our acoustic listening devices amplify this signal, filtered for background noise, so we can walk a grid pattern and triangulate the loudest point — often to within 6–12 inches of the actual break.
🌡️
Infrared Thermal Camera
Active water leaks — hot or cold — create a temperature differential on the surfaces they contact. An infrared camera shows these differentials as color-coded heat maps, revealing the wet zone inside a wall or under a floor without any cutting. A cold water leak behind drywall appears as a spreading blue-gray cool zone; a hot water leak shows the inverse.
📉
Pressure Decay Testing
Pressure decay testing is the standard by which we confirm a leak is present before committing detection equipment time. It also tells us approximately how significant the leak is — a rapid pressure drop vs. a slow one indicates the size of the escape point.
💨
Tracer Gas Detection
For leaks that don't produce sufficient acoustic signature — very slow leaks, polyethylene pipe, or leaks deep under concrete — we can introduce a nitrogen/hydrogen tracer gas mixture into the isolated pipe and use a calibrated gas detector at the surface to find where the gas escapes. The detection sensitivity can locate leaks that produce no discernible pressure drop during a standard timed test.
What We Locate
Hidden Leak Types We Find and Document
Our detection service covers the full property, not just the obvious locations.
Under Slab
Slab Leak Detection
Supply lines run under or through the concrete slab in most slab-on-grade homes. When these lines fail — from corrosion, shifting, or manufacturing defects — the leak is invisible from the surface but audible to acoustic equipment. We walk the floor on a grid pattern, map the loudest detection points, and triangulate to a specific floor location, typically within a square foot.
In-Wall
In-Wall & Ceiling Leak Detection
Wall and ceiling leaks are often traced by following a visible stain to its apparent high point — but the visible damage can be several feet from the actual pipe failure due to how water travels down framing members. Thermal imaging reveals the wet zone accurately, and acoustic equipment confirms the pipe location within the wall cavity.
Water Main
Underground Supply Line Detection
We mark the ground above the detected leak location so the repair crew opens only the section they need to.
Pool & Irrigation
Pool Line & Irrigation Leak Detection
Irrigation system leaks in main supply lines and lateral runs are found by isolating zones with the irrigation controller and pressure-testing each zone individually. Zone by zone testing narrows the failure to the smallest possible section.
Commercial
Commercial Property Leak Detection
Multi-story buildings, commercial kitchens, retail spaces, and industrial properties have complex pipe networks where a supply or drain leak can go undetected through multiple floors before surfacing. We approach commercial detection systematically — zone by zone pressure isolation, thermal scan of suspect surfaces, and acoustic confirmation.
Documentation
Leak Detection Report for Insurance
We format detection reports specifically for insurance submission and can provide documentation on our detection equipment and methodology to claims adjusters on request.
From Water Bill Spike to Confirmed Leak Location — 4 Steps
Here's exactly how a Masters Plumbing Service leak detection call plays out.
1
Initial Water Loss Confirmation
This step confirms we're looking for a real leak rather than meter error or a normal appliance cycling.
2
Zone Isolation & Pressure Decay
We isolate the supply system into zones — hot side, cold side, and if possible, individual branches — and pressure-test each zone to determine which branch is losing water. This narrows the area of active search significantly before detection equipment is deployed.
3
Detection Equipment Deployment
Within the isolated zone, we deploy thermal imaging first — scanning walls, floors, and ceilings for moisture anomalies. Then acoustic equipment confirms the specific pipe location and narrows it to the tightest possible point. Tracer gas is added if acoustic results aren't conclusive.
4
Written Report & Repair Options
Insurance claims: the report is formatted to support a claim for water damage from a concealed leak. We can provide supplemental documentation on request.
Customer Reviews
What Customers Say About Our Detection Service
★★★★★
High-efficiency home with a leak that defied normal detection. Water loss was slow — about 1.5 gallons per hour. The tech used tracer gas after pressure testing confirmed the loss but acoustic detection couldn't localize it clearly. Gas detection found the escape at a micro-fitting under the slab in the utility corridor. Impressive work.
— C. Thornton, Eddy
★★★★★
Ceiling stain in the living room kept coming back despite two drywall patches. Masters Plumbing Service ran the thermal camera and found the wet zone was traveling from a supply line joint 9 feet away and flowing down a horizontal framing member — explaining why the patch kept failing. They marked the actual pipe location, we opened 8 inches of wall there, and the repair held. No more stain.
— B. Osei, Eddy, TX
★★★★★
Commercial building where water costs were running 40% above baseline for six months. Masters Plumbing Service ran a systematic zone-by-zone pressure isolation across four floors, narrowed the loss to the third-floor kitchen supply branch, and located the failure with thermal imaging at a concealed valve body in the ceiling. No damage to the finished ceiling.
— T. Anand, Eddy, TX
Common Questions
Leak Detection Questions We Answer in Eddy
The most reliable self-check: shut off every fixture and appliance in the house, then watch the water meter for 15 minutes. Any movement — including the small leak indicator dial — means water is escaping the supply side somewhere. If the main meter dial moves with everything off, you have a leak. Call us to locate it.
The repair itself requires physical pipe access, which typically means a small, targeted opening. But that's a completely different proposition from opening large wall sections while searching for an unknown leak location.
For pressurized supply lines in concrete or metal pipe, acoustic detection is typically accurate to within 6–18 inches under ideal conditions — quiet environment, no interference from other water use, metal pipe conducting sound clearly. Thermal imaging is accurate to the size of the wet zone it reveals, which varies based on how long the leak has been running and how far moisture has migrated.
Yes. Our written detection report includes: technician credentials, equipment identification, pressure test methodology and results, detection method description, leak location with reference measurements, and supporting thermal imagery. This is the documentation format most insurance adjusters require to approve a concealed-leak water damage claim.
A standard residential leak detection — confirming water loss, isolating the failing zone, and deploying detection equipment to locate the failure — typically takes 1.5–2.5 hours. More complex scenarios (multi-zone commercial, large properties, very slow leaks requiring tracer gas) can run 3–4 hours.
The repair quote is given before any wall or floor is opened. You know the full cost of detection + repair before anything is cut.
Service Area
Serving Eddy and the Surrounding Eddy, TX Region
Our detection technicians are equipped with acoustic, thermal, and tracer gas tools for the full range of leak scenarios found in Eddy, TX homes and commercial properties.
Non-Invasive Leak Detection in Eddy, TX — Book Your Appointment
Masters Plumbing Service's detection team finds hidden leaks in Eddy homes and commercial properties using equipment that eliminates guesswork. The detection appointment pays for itself the moment it prevents one unnecessary wall opening.
